Для ботов
- The ultimate Putty (SSH) Guide
- Putty Serial COM connection does not work
- Intel® Edison Board User Guide
- How to Use PuTTY for a Serial Connection
- Download PuTTY: latest release (0.73)
The ultimate Putty (SSH) Guide
Jump to navigation. A few integrated development environments are suggested. The following table describes the content of the section with the link to each page. Assembly hardware. Direct current DC power supply rated as follow:. However, you can power your board over USB if you do not have an external power supply. For details, see the Powering your board over USB section. Note : The expansion board is stored in a static shield bag as it is prone to damage caused by electrostatic discharge ESD. When not working with the assembled board, or when outside protected areas, make sure to enclose the device back in its static shield bag. When assembling the board, make sure to comply with the ESD handling protection rules. You will need two micro USB to standard type-A cables during initial development setup. Note : The mini breakout board is stored in a static shield bag as it is prone to damage caused by electrostatic discharge ESD. Caution : Unless you make sure your board is seated properly, it may not work or turn on at all. When you turn the attached module and expansion board on their side, both pieces should fit evenly and sit in parallel with each other. Refer to the image below for an overview of the various connectors on your board and what each is used for. See the section Setting up a Serial Terminal. However, you can power your board over the micro type-B USB if you do not have an external power supply. For details, see Programming, powering, and writing to the on-board flash memory. You will know that your board is fully initialized when your computer mounts a new drive much like inserting a SD card into your computer. If you do not see a new drive, or if the LED light DS1 on the Arduino expansion board is occasionally blinking, check the connection of your power supply. However, you can watch the full boot up sequence whether for fun or for debugging purposes by creating a serial communication session with your board. Steps to do so are included in Setting up a serial terminal later in this guide. If you do not see a new drive, and you are powering the board by USB, it is likely that the board is not getting enough power from the USB port. Note : The installation requires administrative rights. Confirm that you allow the program to make changes to your computer by selecting Yes when prompted with the question "Do you want to allow the following program to make changes to your computer? You can rerun the setup tool to update the OS image of your board, reinstall the drivers, or set a new password for your board. Note : The setup tool is not just for initial setup. If they are not, install them from the FTDI page. The setup tool lets you install the necessary drivers and update your board OS image. See Installation and Setup with the Setup Tool. These drivers enable important features, such as:. The IDE you use to program your board depends on the programming language you want to develop in. The choices are:. It's important to keep your firmware up-to-date to ensure the best stability and performance for your board. Simply follow the onscreen prompts to flash your board. For steps for your host system, see the steps for Windows or Mac. If you run into difficulties, need to revert changes, or have other issues, you can use the manual process described in this section.Putty Serial COM connection does not work

This page contains download links for the latest released version of PuTTY. Currently this is 0. When new releases come out, this page will update to contain the latest, so this is a good page to bookmark or link to. Alternatively, here is a permanent link to the 0. Release versions of PuTTY are versions we think are reasonably likely to work well. However, they are often not the most up-to-date version of the code available. If you have a problem with this release, then it might be worth trying out the development snapshotsto see if the problem has already been fixed in those versions. Package files You probably want one of these. They include versions of all the PuTTY utilities. Not sure whether you want the bit or the bit version? Read the FAQ entry. The installer packages above will provide versions of all of these except PuTTYtelbut you can download standalone binaries one by one if you prefer. You probably want one of these. Browse the documentation on the web. HTML: Contents page. Zipped HTML: puttydoc. Plain text: puttydoc. Unix source archive. Compiled executable files for Windows on Arm. These are believed to work, but as yet, they have had minimal testing.
Intel® Edison Board User Guide

When the core is in listening mode Flashing blue the core appears in device manager and using the terminal I can get the device ID. Would be much appreciated if someone could help me out, thank you. Could you try disconnecting putty beforehand, or restarting it after the Core, and see how that goes? I assume this is the same problem. BDub and mdma are presently assessing whether Spark. I am having the same issue that started this post. Although the solution posted is not appropriate for what is going on. I flash and test the Photon and use puTTY to obtain debug information. I have to reboot the Win 7 machine to start another debug session which certainly takes forever. I attempted to disable and enable the COM3 port using the device manager on Windows. But it just hung trying to disable COM3. Although aborting the process and trying again did show COM3 as disabled. Enabling the port also hung and stopping and starting the manager once again, showed the device enabled again. But it still would not allow access to COM3. Any suggestions on what else to try? I am not sure where the COM3 driver for the Photon is coming from. Maybe there is another driver to use that might not cause COM3 to hang up like it is now. Have you tried closing the PuTTY session before reflashing? Does COM3 come back then after the flashing? My super plain term could be an alternate option. Mostly because it auto-reconnects. Could someone please help me with a similar issue? Using Windows 10 and Putty. All worked fine and then I noticed I was using a different com port to get things working.
How to Use PuTTY for a Serial Connection

PuTTY is an open source terminal emulator, used to connect to SSH, telnet and similar servers for remote administration. Developed by Simon Tatham, who released the first version inPuTTY has been upgraded a number of times over the years to add new features and fix bugs. PuTTY also enables you to connect to a device attached to the serial port on the computer, sending typed commands to the serial device and displaying the reply. This is useful for debugging networking hardware equipped with serial ports, or connecting to microcontrollers and other electronics devices. Click on the "PuTTY" icon to launch the program. Type the baud speed the serial device operates at in the Speed box; for example 9, orIf you are unsure of the baud rate to use, check the documentation for the serial device. If no documentation is available, start at a high speed such as , and work your way down until you can connect to the device successfully. Click on the "Serial" menu item under Connection in the Category menu tree on the left side of the PuTTY window to change the default parameters, if necessary. You can set the number of data bits and stop bits, as well as the parity and flow control method used to connect to the serial device. If you are unsure of the settings to use, leave these set to the default values, which will work in the majority of cases. Click the "Open" button to initiate the connection to the serial device. You may see some introductory text sent from the serial device when the device has connected, but some devices do not respond until you send a command. Once you have typed some data and pressed the "Enter" key to transmit to the serial device, you should see a response from the device displayed in the PuTTY window. Close the PuTTY window by clicking on the close button to end the serial connection when required. By : Gareth Downes-Powell. Share Share on Facebook. The serial port was used to connect peripherals before the development of USB. Get great tech advice delivered to your inbox. Keep your family productive, connected, entertained, and safe. Please enter a valid email.
Comments on “Putty serial”